The pads are rated for operation to 1 GHz. The (dB) loss produced is equal to the pad value printed on the top of the pad. Pads are used during station balancing to adjust signal levels as needed. Plug-in pads produce flat (even) loss across the forward and reverse frequency spectrums. Cable Gland O-Ring SpecificationsĬonnect to Cisco 16x4 Coaxial Media Converter console port, 6Pin, FEMALEĬONNECTOR, D-SUB, 9Pin, FEMALE, SOLDER TYPE The cable gland with two holes should be selected when 1+1 redundancy is used for outside PON ONT connectivity. There are two types of cable glands: with one hole and with two holes. The cable gland is a waterproof part used for the RJ-45 port. Same as Cisco GS7000 Node Signal Director – JumperĬable Gland with O-Ring Specifications (RJ45 waterproof connector) Same as Cisco GS7000 Node Signal Director – two way Splitter Same as Cisco GS7000/Gainmaker Node Forward Linear EQ Subscriber Connector/Angle-Polished Connector (SC/APC) Adaptor PoE watchdog: It enables the switch to automatically detect port status and restart failed ports to recover connection in case of IPC connection exception.F-Connector with O Ring, from 5/8” to Metric (M10x0.75mm)į-Connector with O Ring, from 5/8” to Standard (3/8”).Long distance PoE: The transmission distance of a PoE port can be up to 250 m, meeting the requirements of wired transmission (bandwidth reduced to 10 Mbps).Signal lines and idle lines supply power at the same time. 8-pin assignment PoE power supply: Supports 8-pin simultaneous power supply (1/2/4/5 positive, 3/6/7/8 negative).Suitable for powering high-power devices. BT 90W: The red ports support IEEE802.3af/at/bt and Hi-PoE standards, with a maximum output power consumption rate of 90W per port.Intelligent PoE: Provides control over power consumption and offers real-time monitoring to ensure power supplies receive priority with important ports.Suitable for harsh environments such as factory, refinery and traffic light control box Industrial 8-Port POE+ Switch:DIN rail mount, wide working temperature (–30 ☌ to +65 ☌ or -22 ☏ to +149 ☏).6KV surge protection. 【INDUSTRIAL DESIGN】Plug-and-play.LINOVISION EOC Converter with built-in heat sink, ensure super reliability and hassle free transmission.【POWER ADAPTER INCLUDED】LINOVISION Industrial 8-Port POE+ Switch with 100~240V input power adapter, output 53V.Support 2 channel DC48-57V redundant power inputs.The total POE budget is 96W.At the same time realtime monitoring POE load device's status and will automatically reboot POE port when the connected device is not active 【BT 90W POE OUTPUT & POE WATCHDOG】The first two red ports of LINOVISION Industrial 8-Port POE+ Switch support the IEEE802.3af/at/bt POE++ standards, providing up to 90W POE injector for high-power POE devices, like POE monitor, POE lighting, PTZ camera, etc.【POINT TO POINT CONNECTION ONLY】LINOVISION ethernet/IP over coax EOC Converter act as MoCA (Multimedia over Coax) in point-to-point connection, transmit video/audio/data/control signal over coaxial cable, so as being used with twist pair.It’s ideal for the CCTV system in elevator cart. ![]() ![]() 100Mbps bandwidth over 330ft regular twist pair cables while 10Mbps over 1485ft for both POE or NON-POE devices. 【POE & IP OVER TWIST PAIR CONVERTER】 Each pair of EOC(Ethernet over Coax) Converter is equipped with 2 BNC to Twist Pair connectors, which enables POE over Twist Pair transmission.【LINOVISION EOC CONVERTER & POE SWITCH KIT】LINOVISION POE Over Coax Converter & Industrial 8-Port POE+ Switch Kit.Max 3000ft PoE transmission for upgrading analog surveillance system to IP surveillance system while using existing coaxial cable(RG59, RG6, RG11 cables).EOC Converter supports POE standards 802.3af (PoE) and 802.3at (PoE+).EOC Receiver powered by POE+ switch while Transmitter should be connected with POE devices or NON-POE devices.
0 Comments
Leave a Reply. |